Software //github.com/SpacehuhnTech/esp8266_deauther
Hardware //github.com/lspoplove/Deauther-Project
WiKi //github.com/SpacehuhnTech/esp8266_deauther/wiki
FAQ //github.com/SpacehuhnTech/esp8266_deauther/wiki/FAQ
Burning tutorial //github.com/SpacehuhnTech/esp8266_deauther/wiki/Installation
Burning tool //github.com/nodemcu/nodemcu-flasher
Firmware download //github.com/SpacehuhnTech/esp8266_deauther/releases
Quick product upgrade tutorial:
1. Download CP2102 driver (//www.silabs.com/products/development-tools/software/usb-to-uart-bridge-vcp-drivers)
2. Download the firmware (//github.com/SpacehuhnTech/esp8266_deauther/releases)
3. Download nodemcu-flasher (//github.com/nodemcu/nodemcu-flasher)
4. Click the gear to select the corresponding binfile. The programming mode selects DOUT. The rate selects 961200. Click Flash start and wait for the progress bar to reach the end and then power on again
Update Log
|
Difference |
Deauther V1 |
Deauther Watch V2 |
Deauther Watch V3 |
|
Battery |
500mah |
800mah |
800mah |
|
3D Print Case |
YES |
YES |
YES |
|
Screen Protection |
NO |
YES |
YES |
|
Battery Indicate |
NO |
YES |
YES |
|
Power Switch |
Plastic |
Metal |
Metal |
|
Charging Current |
0.5A |
0.8A |
0.8A |
|
RTC DS3231 |
NO |
YES |
YES |
|
Breakout GPIOs |
NO |
YES |
YES |
|
Color |
Black |
Black&White |
Black |
|
Laser |
NO |
NO |
YES |
|
Work Time |
3-4h |
7-8h |
7-8h |
|
Weight |
50g |
61g |
78g |
|
Size(LxWxH mm) |
48x39x17 |
55x50x19 |
60x55x22 |
What is it?
Deauther Watch is still an ESP8266 development board, but you can wear it like a smartwatch.
It comes installed with the latest ESP8266 Deauther software. With this software, you can perform different attacks to test WiFi networks.
Please note that the ESP8266 does only support 2.4GHz.
You can also use it to develop your own software. It is simple to use, just like any other ESP8266 development board.
Function
-
Deauther Attack: Disconnect 2.4G WiFi
-
Deauther Beacon: Create fake networks
-
Deauther Probe:Confuse wifi trackers
-
Packet Monitor:Display wifi traffic
-
CLock:Real Time Clock Adjustable
-
Laser:Powerful Laser can reach 50-100m
GPIOs and Hardware info
-
Display: SH1106 1.3″ OLED
-
Display SDA: GPIO 5
-
Display SCL/SCK: GPIO 4
-
WS2812b LED: GPIO 15
-
Button Up: GPIO 12
-
Button Down: GPIO 13
-
Button Select: GPIO 14
-
Laser: GPIO 16
-
Side Button: GPIO0,RST
Why did you make it?
I designed this development board especially for Spacehuhn’s great project:ESP8266 Deauther. It has been authorized by him and is officially supported.
Thanks to every customer that leaves feedback! I will keep improving this board.
What makes it special?
-
Only ~80mA power usage
-
800 mA charging current
-
Up to around 8-10 hours work time
-
Arcylic cover and 3D print transparent case
-
Powerful laser for fun
-
Indicate charging LED (25%,50%,75%,100%)
-
Included 5dB FPC antenna
-
Power Switch (Click to turn on, double click to turn off,long click to open flashlight)
-
Protection: short, overcharging, over discharging, temperature
-
Added Extremely Accurate DS3231
Disclaimer
This project is a proof of concept for testing and educational purposes. Neither the ESP8266, nor its SDK was meant or built for such purposes. Bugs can occur!
Use it only against your own networks and devices! Please check the legal regulations in your country before using it. We don’t take any responsibility for what you do with this program.
More Info
Deauth
Closes the connection of WiFi devices by sending deauthentication frames to access points and client devices you selected. This is only possible because a lot of devices don’t use the 802.11w-2009 standard that offers a protection against this attack. Please only select one target! When you select multiple targets that run on different channels and start the attack, it will quickly switch between those channels and you have no chance to reconnect to the access point that hosts this web interface.
Beacon
Beacon packets are used to advertise access points. By continuously sending beacon packets out, it will look like you created new WiFi networks. You can specify the network names under SSIDs.
Probe
Probe requests are sent by client devices to ask if a known network is nearby. Use this attack to confuse WiFi trackers by asking for networks that you specified in the SSID list. It’s unlikely you will see any impact by this attack with your home network.
Videos
DSTIKE Deauther Watch V3 Quick Video
How do I assemble deauther watch V3
How to install antenna of deauther watch
How to increase the maximum effect of antenna
How to install DSTIKE Arduino environment
How to use 8266 flash tool flash deauther firmware
4 GREAT REASONS TO BUY FROM US:
- Over 37,000 happy customers worldwide
- Real people on our support team ready to help
- The finest materials and stunning design — all our products are developed with an obsessive dedication to quality, durability, and functionality
- We use the most secure online ordering systems on the market, and are constantly improving our software to make sure we offer the highest possible security
BUY WITH CONFIDENCE
Our mission is to make your shopping experience as safe and enjoyable as possible. Have questions? Feel free to contact our award-winning customer care team for advice on everything from product specifications to order tracking.
- Money back guarantee: Something not quite right? If you’re not totally satisfied with your purchase, you can return it within 15 days for a full refund
- Risk-Free Purchase: We utilize industry-standard Secure Sockets Layer (SSL) technology to allow for the encryption of all the sensitive information, so you can be sure your details are completely safe with us
- Trustworthy payment method: We partner with the most popular online payment solutions that guarantee enhanced security and fast transaction processing
